Home
:Categories
:Conformal Coating
:Fine-L-Kote HT High-Temp Silicone Conformal Coating

Fine-L-Kote HT High-Temp Silicone Conformal Coating

Silicone coating engineered for superior thermal and moisture resistance

Request A Sample

Part #	Name	Size	Units Per Case	Price Per Case	Case Qty
2106-12S	Fine-L-Kote HT - 12oz aerosol	12 oz (340g)	12	$454.56
2106-G	Fine-L-Kote HT - 1 gal liquid	1 gal (3.8L)	1	$385.54

Packaging Order minimum case quantity only. Extra shipping fees may apply.

Order from an authorized distributor

High Temperature Silicone Coating is designed to prevent thermal breakdown at high temperatures. SR provides good chemical resistance, moisture and salt spray resistance, and is very flexible. Silicone conformal coating isn’t abrasion resistant because of its rubbery nature, but that property does make it resilient against vibrational stresses. Silicone coatings are commonly used in high humidity environments, like outdoor signage.

For more information, check out our Essential Guide to Conformal Coating.

Features & Benefits

Designed for high temperature environments
Fast-drying silicone 1-step process
UL94 V-0 rated
Thermal resistance - to 662°F (350°C)
Dielectric strength - 560 volts/mil
Meets IPC-CC-830B
Passes the laboratory tests of MIL-I-46058C. However, it is not qualified on QPL-46058.
Moisture resistant
Vibration resistant - flexible
UV indicator for black light inspection

Applications

Electronic Assembly

FAQ's

What is the difference between full cure and tack-free cure?

Full cure is when it meets all the final specifications. There might be some out-gassing, but it will be as hard as it is going to be, and adhesion is as good as it gets. Tack-free is as the name suggests, not sticky so you can move it along the assembly process.

What is the difference between dielectric strength and dielectric withstand voltage?

The dielectric strength is material intrinsic property and withstand voltage is surface property which depend on thickness of the material. They can be slightly different for thicker materials, but for conformal coating, the two numbers should be very close or the same. That is because we test coating at 3-5 mils thickness, calculate, then report the value per mil.

What type of UV light / black light should I use for QC inspection of the final conformal coating?

Conformal coating with UV tracer can be inspected with any typical UV lamp which has wavelength of 320-380 nm.

How do you apply liquid conformal coating? (2106)

Apply to clean, moisture-free surface. Areas not requiring coating should be masked. Application: Coating may be applied by spraying, brushing, dipping or flow coating. Allow coating to flow around components. Cure: A 1.0 mil coating will be tack-free in 45 minutes. Full cure requires 24 hours @74˚F/23˚C. Heat Cure: 15 minutes @120˚F/49˚C. An open vessel of water placed in the drying chamber will facilitate curing. UV detectable for QC inspection. Removal: Coating may be removed by soaking in Conformal Coating Remover. Use TraceTech™ Conformal Coating Remover Pen for spot removal. After the new component is installed, areas should be cleaned and re-coated.

How do you use an aerosol conformal coating? (2106-12S)

Shake well. SURFACE MUST BE CLEAN & MOISTURE FREE. Areas not requiring coating should be masked. Coating: Spray top to bottom, allowing coating to flow around components. Rotate board 90˚ and repeat process 2 or more times. If nozzle clogs, clean with solvent or use new nozzle. Cure: A 1.0 mil coating will be tack-free in 45 minutes. Full cure requires 24 hours @74˚F/23˚C. Heat Cure: 15 minutes @120˚F/49˚C. An open vessel of water placed in the drying chamber will facilitate curing. UV detectable for QC inspection. Removal: Coating may be removed by soaking in Conformal Coating Remover. Use TraceTech™ Conformal Coating Remover Pen for spot removal. After the new component is installed, areas should be cleaned and re-coated.

When using conformal coatings in general, what causes a "milky" cure or white "foam" on the substrate?

In almost all cases, the cloudy or milky cure comes from coating in higher humidity conditions. The white foam (from an aerosol) is caused the same way. We have the following suggestions: 1) If possible, allow the substrate and coating material to come to approximately the same temperature when applying. 2) Avoid applications in RH > 60%. High humidity ranges will discolor some coating resins and will start curing others. Besides the aesthetic value, it certainly may affect adhesion to the material. 3) Specifically on the silicone coating, if the resulting application is foamy, increase the focal point of the can, ie back off to about 10 -12” from the substrate & make 2 -3 light passes rather than one heavy pass to coat the board.

What types of coverage areas are to be expected with the conformal coatings in general?

Wet film thickness = Sq. ft. per gal.
0.1 mil = 16,040
0.5 mil = 3,210
1 mil = 1,600
2 mil = 802
3 mil = 535
4 mil = 401
5 mil = 321
6 mil = 267
7 mil = 229
8 mil = 201
9 mil = 178
10 mil = 160

How do I figure out the shelf life of a product?

The shelf life of a product can be found on either the technical data sheet (TDS), available on the product page, or by looking on the certificate on conformance (COC). The COC can be downloaded by going to https://www.techspray.com/coc. Once you have the shelf life, you will need to add it to the manufacture date for a use-by date. The manufacture date can be identified by the batch number. The batch code used on most of our products are manufacture dates in the Julian Date format. The format is YYDDD, where YY = year, DDD = day. For example, 19200 translates to the 200th day of 2019, or July 19, 2019. This webpage explains and provides charts to help interpret our batch numbers: https://www.techspray.com/batch-codes.

More FAQs

Articles

The Essential Guide to Waterproofing Electronics

This article throws light on the detrimental effects of moisture on electronics, and presents strategies to keep moisture away from electronics. Finally, some products from Techspray are highlighted which would aid manufacturers and end users prevent moisture from entering electronics.

Read This Post

3 Testing Standards That Separate Conformal Coating From Shellac

As an electronic manufacturing services (EMS) supplier, you are required to think on your feet and are forced to gain new capabilities as your customers’ specification change. This can be daunting, especially when you try to bring conformal coating manufacturing in-house and make material and equipm...

Read This Post

How To Identify and Cure The Top 7 Conformal Coating Defects

In this post well take a look at the 7 common conformal coating defects, their causes, and how to prevent. Read this post to avoid issues in your conformal coating process selection and application.

Read This Post

The Essential Guide to Conformal Coating

Conformal coating improves PCB reliability, providing increased dielectric resistance, operational integrity, and protection from corrosive atmospheres, humidity, heat, fungus, and airborne contamination such as dirt and dust. Conformal coating are a special polymeric film forming product that prote...

Read This Post

Video Guide to Removing Conformal Coating

Today I’m going to cover the process of removing conformal coating from a printed circuit board using a solvent-based coating remover or “stripper”. This might be required when repairing or refurbishing electronic devices. There are solvents that are effective of acrylic, silicone and urethane confo...

Read This Post