Anti-Static Freezer

Sku Number Name Size Units
Per Case
Price
Per Case
Case
Qty
 
1747-10S Anti-Static Freezer 10 oz (284g) 12 $267.96
Packaging Order minimum case quantity only. Extra shipping fees may apply.
Order from an authorized distributor
Diagnostic freeze spray for static sensitive assemblies.   Rapidly evaporating liquid that super-chills isolated areas. Used as a troubleshooting aid for intermittently faulting capacitors, resistors, semiconductors, and other defective components. It also increases visibility of cold solder joints, cracks in printed circuit boards and oxidized junctions. Contains additive that avoids static build-up, critical when working with ESD-sensitive components.

Features & Benefits

  • Avoids static build-up
  • Nonflammable
  • Non-ozone depleting
  • Moisture free
  • Zero residue
  • Safe on plastics
  • Chills down to -60°F (-51°C)

Call-outs: Delco C00054786, HP 8500-6344, NCR 603-8001308

FAQ's

How do you use freeze spray?

For failure isolation, energize the suspect PC board. Spray on board to determine the area where the failure is occurring. Attach extension tube and spray on individual components until the failed component has been isolated.

How do I properly dispose of an aerosol can after it is empty?

It may be different state-by-state, so contact your state environmental agency for regional specific regulations. For a general guideline, here is the process according to EPA hazardous waste regulations 40CFR. The can has to be brought to or approach atmospheric pressure to render the can empty. Puncturing is not required, only that it “approach atmospheric pressure”, i.e. empty the can contents until it’s no longer pressurized. This insures that as much contents as is reasonably possible are out of the can. It is then considered “RCRA-empty”. At that point it can be handled as any other waste metal container, generally as scrap metal under the recycling rules. Note that the can is still considered a solid waste at this point (not necessarily hazardous waste).

Is there something I can do with the extension tube (straw) so it doesn’t get lost?

The aerosol trigger sprayers that are common on dusters, freeze sprays, and flux removers, have two ways to store the straw when not in use. The hole at the back of the body of the sprayer is just the right size for the straw to slide into place for storage. The slot below the trigger is also the right size for the straw to snap into place, which also has the advantage of locking the trigger.

How do I figure out the shelf life of a product?

The shelf life of a product can be found on either the technical data sheet (TDS), available on the product page, or by looking on the certificate on conformance (COC). The COC can be downloaded by going to https://www.techspray.com/coc. Once you have the shelf life, you will need to add it to the manufacture date for a use-by date. The manufacture date can be identified by the batch number. The batch code used on most of our products are manufacture dates in the Julian Date format. The format is YYDDD, where YY = year, DDD = day. For example, 19200 translates to the 200th day of 2019, or July 19, 2019. This webpage explains and provides charts to help interpret our batch numbers: https://www.techspray.com/batch-codes.

Articles

Techspray Products Control ESD and Improve Reliability
Electrostatic discharge happens all the time, especially in dry climates and in the winter season, when there isn’t moisture in the air to help bleed the excess electrons (water is conductive, so allows the electrons to flow more easily). Normally it is nothing more than an irritation, but with sens...
Read This Post

Using Freeze Spray to Diagnose Faulty Electronics
Freezer is used to test electronic equipment for and locate thermal intermittent components and systems, provide heat sink protection for heat sensitive components during soldering and desoldering, perform low-temperature testing of prototype circuitry and electromechanical systems, and locate hairl...
Read This Post
You did not finish submitting your information to request a sample